Thanks for letting us know. Did this article help you? Try to keep your fingers in place to hold your bowtie in place. Sew a straight stitch about 0. Place the pattern piece on your folded fabric and insert a few pins through the pattern and fabric layers to secure them.
It will be concealed in the next steps. Fold the tail back to the right until you reach the middle of the rectangle. This is to help make wrapping your bowtie easier. Now for some pics! Pick up your Bowtie and turn it to the front. Turn the tail of the tie to where the inside if the tail is facing you. It may feel a little weird in the back but don't worry, it's normal. Wrap the tail of the tie up the middle of the Bowtie and around to the back. The back of the Bowtie may look a little busy but no one will see that part.
It will all come together, trust me. This is what your Bowtie looks like in the front. Make sure to pull the tail down snug so the bowtie can cinch nicely. Try to keep your fingers in place to hold your bowtie in place. Try to straighten the inside corners of your Bowtie while you're still wrapping the tail. However, do not use pins. They may damage the felt and you will not be able to complete the bow tie with a pin in place.
Squeeze in the bow at the center. With your other hand, pick up the rectangle at the center and squeeze it in to create 3 even folds. The center should look like an accordion when you do this. There should be 3 distinct, even folds in the center of the tie. Glue the bow between the folds with a hot glue gun. Heat up the hot glue gun about 15 minutes before you plan to use it. When the glue gun is warmed up, loosen your grip on the center of the tie slightly to expose the area between the folds.
Then, apply a dot of hot glue between the folds. Secure the strip of felt around the center of the bow with hot glue. Take the strip of felt and wrap it so that the short ends overlap on the back side of the bow tie. Then, apply a couple of dots of hot glue to the felt to secure the 2 ends to the back of the bow tie and to each other.
Attach the bow tie with a safety pin or ribbon. This completes your bow tie! Attach it to your shirt collar with a safety pin through the backside of the bow tie. If you want to wear the bow tie around your neck like a choker, then you can hot glue or pin a piece of ribbon to the back of the bow tie and then tie the bow around your neck.
Choose a fabric for your bow tie. Cotton works well for making a bow tie, but you can use any fabric you like as long as it is flexible enough to shape into a bow tie. Choose something in the color, texture, and weight of your choice.
Purchase fabric from an online fabric store or a local craft store. You can also upcycle unwanted clothing from your own closet, such as an old, cotton dress shirt or skirt. Find a simple bow tie pattern. You can purchase a pattern from a craft store or download and print a free pattern from the internet. The pattern you use should look like a long strip with a couple of wider spots.
This will allow you to create a bow tie that you can actually tie, rather than a clip-on tie. Cut the fabric and interfacing for your bow tie shape. Place the pattern piece on your folded fabric and insert a few pins through the pattern and fabric layers to secure them. Cut the fabric right along the outer edges of the pattern.
Do not cut through the pattern or too far outside of the edges. Then, repeat this with the pattern piece on the folded interfacing. Iron the interfacing onto the fabric. Lay out 1 of your fabric bow tie pieces so that the wrong back side of the fabric is facing up.
Then, place 1 of the interfacing pieces over the fabric piece. Line up the edges of the interfacing and fabric so that they are even. Run the heated iron over the interfacing to secure it to the fabric. Repeat this for the other fabric and interfacing pieces.
Sew the long edges of the 2 interfaced fabric pieces together. Line up the 2 pieces so that the right sides are facing each other and the edges are aligned. Sew a straight stitch about 0. Sew around the short end on 1 side of the tie as well, but leave the other end open. You will invert the pieces after sewing them together.
Flip the inside of the bow tie out. This can take a little patience, as it can be difficult to pull the whole tie through the small opening left on 1 side of the tie. To make it easier, try using the eraser end of a pencil to help you push 1 end of the tie through the tube of fabric and out the other side. Sew the remaining short edge of the tie. On the remaining open end of the tie, flip the raw edges inward by about 0. This will secure the open end of the bow tie.
If desired, you may also sew a straight stitch across the other short end of the tie so that the ends of the tie match each other. Iron your bow tie. Ironing will make the tie look neat and crisp after it is tied. Place the bow tie on a flat surface, such as an ironing board or over a towel on a table or counter. Then, run the heated iron over the fabric to flatten it out, especially along the seams. Make sure that the tie is free of bumps, creases, and wrinkles when you are finished.
If your tie is made from a delicate fabric, then you may want to place a t-shirt or thin towel over the tie before you iron it. Place your iron on its lowest setting as well. Try on the bow tie. After you finish ironing the bow tie, tie it around your neck to try it on. A scrap of fabric from the remnants bin at your local fabric store should provide plenty of fabric.
Cotton works best, but you can use any lightweight fabric you want. Use your ruler to measure the fabric and mark where you need to cut it with a piece of chalk. Then, cut along the chalk lines to get the 2 pieces.
Fold the square piece in half with the wrong sides facing out. Then, add a line of hot glue along the raw edge on the right print side of the fabric.
Put your finger on the tie where you envision the location of the bow tie's knot in the center of the rectangle. Pinch the long side of the tie and create a concave arch with the material, creating a crease along the seam on the underside of the tie. The next loop creates the center knot of the bow tie. The bow tie is a descendant of the knotted cravat. It was born from the need for neckwear that was easier to wear than the cravat and that would last throughout a more active day. By the end of the 19th century, the butterfly and batwing bow tie were commonplace. Oct 29, · You want this to look as close to a bow tie as possible, in order to give it those two extra back flaps you need to fold it two more times. To do this simply put your hand over the fold you already made and fold over .